What’s under the caulk? If it’s ceramic tile, you can probably get away with a brass cup brush in a drill. Test in an inconspicuous area first obviously, but it should be less likely to scuff up the surface as something like scotchbrite.
What’s under the caulk? If it’s ceramic tile, you can probably get away with a brass cup brush in a drill. Test in an inconspicuous area first obviously, but it should be less likely to scuff up the surface as something like scotchbrite.
After referencing actress-comedienne and Trump supporter Roseanne Barr earlier in the interview, Grammer was asked by host Justin Webb if he was still a supporter of the former president.
“I am,” Grammer said. “And I’ll let that be the end of it.”
🤮
Suppressors do exist. And are commonly used in close quarters combat. Especially by well funded combatants like the IDF.
I doubt he’s broke. Far more likely that he’s just a bigot.
Getting all the old grease off isn’t super important. You mainly just want to get it clean enough to make sure the bearing surface on it and the ball on the back of the drum are smooth and not getting scratched/galled up.
I have about the same dryer I’ve been keeping alive for years. I wouldn’t worry too much about the dull spot. That’s likely where the old coil got a hot spot before it failed. It’s just discolored the zinc coating. Shouldn’t effect heat dissipation but it might be more susceptible to rust now.
If you’re not in a big hurry, I would replace that white plastic bearing the drum rides on (you can see it on the very left in the last picture). It’s super squeaky when it fails. If you don’t replace it, at least give it a dollop of high temp grease.
it’s interesting to see the drone’s perspective for a change.
The Russia/Ukraine conflict has really shown the drone’s place on the battlefield. It’s awesome; and terrifying.
What a convenient find.
I don’t mean it’s good for them to ride the whole race out, that is just a spoiler vote. But at this early point it’s good to have left leaning opponents out there to force democrats to answer questions that may be popular with the public but they wouldn’t ask themselves if they were running opposed.
Pre-primary 3rd party candidates have their place. They can attend debates and can force their opponents to concede to popular ideas for fear of losing votes. Past that, yes they are just spoiler votes in our two party system.
Are you really blaming Nader for the 2000 shitshow?
Edit:
The national Democratic Party is the farthest left it’s been since before Watergate
That’s still not left enough for me.
While 3rd party candidates aren’t even remotely viable until we get ranked choice voting; Anything that helps to pull centrist dems left is a good thing.
Better one: https://apnews.com/article/hunter-biden-plea-deal-taxes-gun-drugs-690d38f1ffae4dfce2c171d21e7d3594
The plea deal was scrapped because “The overlapping agreements created confusion for the judge”
It sounds like you are looking for something like this: https://www.adafruit.com/product/2210
If you look around the site, there are lots of helpful tutorials to get you started with it and also help you adapt it to your needs. They also sell most of the extra parts you would need. For example you could add this to make it motion triggered. Their parts aren’t the cheapest tho, you are paying for the ease of use, excellent documentation, and tutorials. If you’re crafty, most of it should be salvageable from e-waste.
Like single frequencies/tones (beeps, boops)? Or more complex sounds (dog barking, voice)? A little more specifics about your project would help us give better info.
I’m sure it’s just nostalgia but I used vBulletin forums for so long, that’s what feels like home.
Pull out as much carpeting as your comfortable taking apart and get some air moving through. The more moving air the better.
deleted by creator
We already have the tech to let signal lights at intersections know emergency vehicles are approaching so they can direct traffic accordingly. No reason this couldn’t be adopted to autonomous vehicles.
They both work fine. I mainly meant if you were having to buy electronic ballasts to make the bulbs you have work, it may be cheaper to buy the bypass bulbs and do away with the ballasts. Same amount of work.
Brass brush on a drill would probably melt into plastic fast. But a handheld one would work ok, or steel if you need more persuasion and aren’t worried about scratches.